First, wooden door installation knowledge
1. Installation conditions
(1) The wooden door must be installed with a reserved opening. It is strictly forbidden to install the side wall.
(2) The wooden door shall be installed after the installation of the groundwork (such as floor tiles and stone) of the opening, and after the wall putty is scraped and polished, the wall shall be attached to the wall and the hole at the stone. Sideways) for installation work.
(3) The humidity of the installation wall is <25%. If the humidity is >25%, the moisture barrier should be installed on the installation wall.
(4) The installation site environment is clean, free of clutter, and no cross work.
2, installation tools electric hammer, woodworking hoe, plane, flat boring, fine tooth saw (gang saw), screwdriver, square ruler, tape measure, hanging hammer, level ruler, electric drill, hole opener, stamp, corresponding specifications drill.
3, installation materials iron joints, 60 nails, 25 and 20 self-tapping screws, 502 glue, towels or cotton yarn, wood cutting, small wooden strips, pig hair brush, styrofoam, milky white glue, door locks, hinges, Door suction, wall moisture-proof material.
Second, the wooden door installation sequence
1. Assemble the door cover.
First find the door cover and the vertical plate. According to the back number, the joints should be on the same plane, and the joints should be glued.
2. Install the door cover.
Put the assembled door cover into the door hole as a whole, and fix the door cover around with the small wooden strip. The two sides of the door cover should be on the same plane as the wall. Then check whether the whole door cover is perpendicular to the ground. The top cover and the two sides of the door cover Whether the two corners of the board are at right angles, whether the door panel is bent or not, and the iron pieces are twisted at both ends to wrap the wall.
3. Install the door leaf.
The hinge groove is opened first, and the distance between the hinge groove and the two ends of the door leaf is preferably 1/10 of the height of the door leaf.
4. Install the door lock.
After loading, check whether the door leaf and door lock switch are flexible, whether the seam is flexible, and whether the seam is in compliance with the specifications.
5. Install the door cover line.
Cut the door line with right-angled edges into a 45-degree angle, trim it with a woodworking planer, insert it into the door pocket at the right angle, and glue the door sleeve wire to the door panel with the floor glue.
6. Install the door suction at the corresponding position.
Third, the wooden door installation skills
When installing the wooden door, first check whether the wooden door components are complete, whether the dimensions of each component are correct, and whether the door is assigned to the corresponding position to match the door hole ruler.
The tips for installing wooden doors are as follows:
1. Please place the goods horizontally on the floor, do not lean on.
2. Painted products should be painted within five days.
3. Try to avoid long-term outdoor sunlight and prevent the wooden door from being heated.
4. Maintain indoor air circulation to prevent the wooden door from getting wet frequently.
5, to prevent the wooden door from being hit abnormally, it is not appropriate to use too much force.
6. It is strictly forbidden to hang heavy objects on the door.
7. Before installing the corner wall and T-wall door, the customer should be notified to make a “fake wall†on the side without the threshold. The width should be no less than 50mm. Determine the width of the “fake wall†according to the width of the line. Otherwise, the door edges displayed on both sides are asymmetrical.
8. The size of the single-swing door, the sub-mother door and the double-seat door opening is (the thickness of the sleeve is 32mm): the door height = the door height + 40mm, the door width = the door width + 65mm. Other types of composite doors are subject to specific conditions (note: the door height refers to the net height from the groundwork that has been completed, the width of the door opening, and the thickness is also the net size).
Fourth, how to supervise the installation of wooden doors
1, the mouth is consistently good.
2. The door leaf and door lock switch are flexible.
3. The gap between the door and the door is the same.
4, the door set vertical plate should be perpendicular to the ground, no bending phenomenon.
5. The door sleeve line is in close contact with the wall surface.
6, the decorative surface is not damaged.
7. Clean the set of solid wood doors after installation and teach the user to accept.
Gsk Cnc Machine,Cnc Lathe Machine,Linear Guide Cnc Machine,Linear Guide Machine,Slant Bed CNC Machine,,Gsk Slant Bed Cnc Machine
Shaoxing Sunfong Intelligent Equipment Inc. , https://www.zjsxsunfong.com