Diatom mud is an indoor decorative wall material with diatomite as the main raw material. It has the functions of eliminating formaldehyde, purifying the air, regulating humidity, releasing negative oxygen ions, fire retardant, self-cleaning walls, sterilization and deodorization. Due to the health and environmental protection of diatom mud, many diversified owners will now use diatom mud to decorate the walls. How should the diatom mud wall be treated? How to maintain it later? Next, take a look with Xiao Bian!
Diatom mud wall base how to deal with
Diatom mud wall surface treatment is generally divided into three situations:
First, rough room
In general, rough housing has been approved as water-resistant putty or white on the wall according to the relevant current standards. It should be noted that if the base surface is firm, flat, clean, free of dust, and the yin and yang corners, it can be directly applied. However, most of the current site conditions require professionals to re-apply for putty or bleaching.
Second, the new wall
The so-called new wall refers to the wall constructed in conjunction with the renovation. Can be roughly divided into three kinds:
1, such as paper surface gypsum board, lightweight partition board, insulation board, cement pressure board and other ramada wall plastering. It must be handled strictly in accordance with the construction specifications and carefully scraped, but it does not need to be sanded.
2, for the wall of the board wall, such as: blockboard, plywood wall surface should be back-oil or atomic gray back cover treatment.
3, different wall materials such as: joinery and lime wall, gypsum board and joinery, gypsum board and the original wall, in the construction process must be patched to avoid the various materials in the drying process due to the speed of time Cause cracking and other phenomena.
Third, the old wall
For a wall that has been painted or painted on an old wall, the wallpaper or paint needs to be removed and re-scratched and dried. If the wall surface of the latex paint should be determined by the circumstances of the wall, such as the drum from the surface, off, cracks must be removed after the latex paint, putty or white after the construction. If the original wall is in good condition, it can be directly constructed. On-site construction, such as wall cracks, empty walls, peeling, turbid water, and moldy hair should understand the causes of the problems and propose solutions.
Diatom mud wall maintenance tips
The diatom mud wall is naturally environmentally friendly and has many advantages, but at the same time it also requires the owner's serious maintenance. In general, the diatom mud wall is the same as other walls and it is relatively simple and convenient to maintain.
1, lines the walls easy to clean up fouling the timing is very important
The diatom mud wall surface is uneven, and it is easy to accumulate dust in long-term use. In this case, simply clean the surface with a simple dry cloth or tweezers.
2, should pay attention to writing footprints rubber sandpaper good helper
If the footprints or handwriting left traces on the wall, the lighter ones can be wiped with an eraser. The deeper traces can be carefully rubbed with fine sandpaper to remove dirt marks from the surface.
3, need to be cautious accidentally contaminated colored liquid as soon as possible
Colored liquids such as coffee and fruit juices are often difficult to clean when they hit a wall. Before the liquid marks completely penetrate the wall, wipe off any residual liquid on the wall with a rag as soon as possible, and then use a cloth dampened with chlorine bleach. Point the surface, wipe the stain a little bit, and it may be necessary to refill the diatom mud.
The above is the related content introduction of diatom mud wall, I hope to help you. For more information on diatom mud, please continue to pay attention to the information on this site.
Diatom mud top ten brand diatom mud
Strainer is used for filter the impurities in the pipe to ptotect pump, valve and equipment function well, Ningbo RMI Plastic Co.,Ltd offer PVC Y type stainer and socket end and flange end fit for DIN, ANSI, JIS, BS, NPT standards, size from 1/2" to 4". also supply T type stainer size up to 12" by material CPVC, PVDF, PPH for industrial chemical application.
Ningbo RMI Plastic Co., Ltd. offer Y Strainer with specification:
Size: DN15~DN100 (1/2 inch ~ 4 inch)
Connection: Flange DIN PN10, ANSI CL150, JIS10K, socket DIN, ANSI, JIS, CNS, BS, NPT, BSPT
Body Material: PVC
Screen material: PP, stainless steel
Sealing: EPFM
Y Strainer,Plastic Strainer,PVC Strainer,Plastic Filter
Ningbo RMI Plastic Co.,Ltd , https://www.rmiplast.com