These walls cannot be dismantled. Generally speaking, the bearing walls must not be moved. Even the large holes in the above areas will not work. Otherwise, the consequences will be serious. There is also a wall below the window of the old house balcony, called the weight wall, is used to balance the gravity of the balcony, there is a certain weight bearing on the balcony, so it is best not to demolish, especially the old house. However, even if the windows and brick walls are removed together, some property companies will allow it. This is mainly based on the specific conditions of the buildings. Compared to the load-bearing walls, the non-bearing walls must bear at least two loads. One is the weight of the wall. Take a six-story residential building as an example, the non-supporting walls of the bottom occupants shall bear the weight of the above five walls, and each meter is long. The wall should bear a weight of 7300 kg. Second, structurally speaking, non-load-bearing walls are often designed as anti-seismic walls. In other words, in the event of an earthquake, these non-load-bearing walls will be subjected to seismic forces together with seismic walls. According to reports, this type of non-load-bearing wall cannot be demolished. Although it is not a big problem for a single family to dismantle non-load-bearing walls or make an opening on the wall, if residents of the whole building are willing to demolish the wall, they will Greatly reduce the building's resistance to earthquakes. There is another kind of wall, that is, after the building is built up, the wall that rises behind a relatively large span is structurally speaking, it is a non-load-bearing wall, but it plays a great role in supporting the house and it is not free to Demolition reform. In addition, the non-load-bearing walls underneath the concrete beams must not be tampered with. Because the beam is made of concrete, but for the weight of the floor and the wall above the beam, the beam does not directly bear the vertical load, but transmits it to the wall below, so the beam itself does not add much steel. Therefore, once the wall below the beam is dismantled, the beam will lose its supporting force and gradually deform or even fall. Which walls can be removed? For example, light structural walls, such as light steel keels, gypsum board walls, or cement board light walls, which are used as partitions for wall demolition, are not dangerous. Such non-load-bearing walls can be dismantled. However, please note that for a half-brick wall of a bathroom, if a supporting beam with a supporting wall is designed in the floor structure, it can be removed, otherwise it cannot be removed. However, even if it can be dismantled, it must be prevented from damaging the waterproof layer, otherwise it will have to be redone.
Demolition of the wall notice of property management approval: the demolition of the wall is not an ambiguity, it is absolutely impossible to judge by the naked eye alone. No matter whether it is any wall, you have to obtain the consent of the property before you want to transform it. Otherwise, it is very likely that the property deposit will be deducted because it violates the requirements of the property. Generally speaking, when the building is completed, the original design unit will leave a drawing for the property company. The wall thickness, material, etc. of the load-bearing wall, non-bearing wall, etc. are marked clearly. According to the drawings, the property company can determine which walls can be removed and which walls cannot be removed. If there are special circumstances, the occupants and the construction team should consult with the property company, and ask the relevant structural design personnel to take timely remedial measures and strengthen the measures that may occur after the demolition. Pay attention to the circuit: In general, there are circuit lines in the wall. Care must be taken to avoid brute construction and break the circuit. At the same time, before the demolition, it is also necessary to consider the direction of the transformation of the circuit in detail. After all, the transformation of the circuit can be used to construct a part of the cost that is very watery. If you don't want the decoration company to make you too much money, it must be planned.
Villa design balcony house room window decoration residential decoration partition partition door bathroom design bathroom waterproof toilet partition bathroom door
LED grow lights are relatively new to the cannabis growing scene,but they have become wildly popular over the last few years with their ability to produce great yields while staying cool and using a reasonable amount of electricity.
Choose LED grow lights if...
You want to use the most cutting-edge indoor cannabis grow lights with a customized spectrum of light
You are willing to do some research to determine the best LED Grow Light for your space
You have some extra money to spend on your initial setup (some of the best LED grow lights are expensive!)
Quality (potency, smell, trichome development) is more important to you than yields/watt.
You don't want to deal with an exhaust system or ducting,and would prefer to just hang your grow light over your cannabis plants and let the lights cool themselves
Features
Deep penetration :Good lighting penetration,can penetrate to the deep of the plants
Modular Internal Build: Fully upgradable,easy warranties
Thermal Management:Custom copper core heatsinks quickly dissipates heat for cool operating temperatures
Powerful: 2nd Generation ultra penetration 5W LEDs light deep into the canopy
Versatile: Power cord available in 85~265V and international plugs
Lighter weight: Much lighter than the same products in the marketplace, safer for hanging .
Plants: Suitable for both vegetative phrase and flowering phrase
Product Images
The Plug you can choose
PAR Value of our 2000W LED Grow Lights
Applications
Our professional full spectrum COB LED Grow Light are suitable for all the indoor plants and good for seeding, growth,flowering and fruiting stages of plants, increasing the harvest and Saving energy.
Our Ageing Test
Package
Cautions:
1.Do not use the lights in dripping water or anywhere where they will get wet, water and electricity can be a dangerous mixture
2. The working environment for the light is -20~40 degree celsius,45%RH~90%RH.
3. To protect the light, Plz cut off the power when there is a lightning strike.
4. Don`t touch or move when the light working.
Suggestions:
1.Clean the dust inside every 6 months to ensure the good heat dissipation and long life time.
2.Don`t keep too short distance to the plant canopy to avert leaves bleaching.
3.Highly hang the lamp will weaken the energy and affect the growth cycle of the plants, so the lamp should not be hang too high.
4.While taking care of the plants, please spray the leaves and branches 2-3 times everyday, to ensure the plants do not wrinkle a wither, and have no phenomenon of few fruit, and hard pericarp.
Philizon have over 6 years' experience in designing and manufacturing led grow lights and LED Aquarium Light. Persuiting to offer the best LED grow lights for plants growth,we cooperate with the scientific research institutes and the Academies of Agricultural Sciences in USA, Australia Canada, UK and so on.A great number of commercial plant growers test the lights, and their feedbacks show that this lamp owns a lot of 640nm,660nm and 740nm lights, which gives the plants enough nutrient in the flowering and fruiting phase and bring a far higher yield than other led grow lights in the market.
Full Spectrum Grow Lights,Flowering Plant Grow Light,Flowering Led Grow Light,Grow Lights Full Spectrum
Shenzhen Phlizon Technology Co.,Ltd. , https://www.szledaquariumgrowlight.com