The use of Taiwan's Yu-Ding industrial remote controllers has become more and more common, and it has become an industrial wireless control field, especially the industrial remote control with the most amount of cranes. However, many people are incapable of using them when encountering faults, and lack basic knowledge to deal with them. , Yancheng Ruijiu Electromechanical Technology Co., Ltd. summed up the following troubleshooting steps of Luoding Industrial Wireless Remote Control for your reference only.
When Ding Ding industrial wireless remote control does not work (ie, the receiver does not respond to the corresponding action when pressing the transmitter button), and no fault message is generated, please follow the simple troubleshooting steps below to check Ding Ding Industrial Wireless Remote Control:
1. Check if the battery power is normal.
a. Check the battery model and installation direction.
b. Check the orientation of the battery compartment.
c. Check the battery level.
d. Check if the connection between the battery compartment and the circuit board is broken.
2. Check if the microprocessor control unit is faulty.
a. Unplug the transmitter key first, then plug the key switch again.
b. If you do not press the "Start" button, press the "Up, Down" and other action buttons directly. The transmitter should quickly flash a red light to indicate that the boot mode is incorrect. If not, it indicates that the microprocessor control unit is faulty or the power supply wiring is abnormal.
c. According to the normal start-up procedure, the power indicator light is red and the magnetic key cannot be started or removed. The magnet is missing or the magnetron on the circuit board is bad. Install a magnet or replace the magnetron. The emergency method can directly magnetize the magnet. The control ends are shorted.
Can't handle it yourself and get it repaired.
3. The transmitter LED is normal, but the receiver is completely unresponsive.
Make sure the receiver power input is normal.
a. Check whether the AC power fuse and DC power fuse are blown. If necessary, switch off the main power supply and replace the replacement fuse.
b. Make sure the wiring between the "receiving high frequency" module and the "relay" module is normal.
c. Confirm that the output fuse of the relay is blown. Replace the replacement fuse if necessary.
d. Confirm that the receiver and transmitter S/N code and the CH channel number are the same.
e. Check if the transmitter quartz crystal is broken or dropped off.
Send repairs
4, an action does not work
Check whether the output fuse of the relay is blown. If necessary, take the spare fuse and replace it with the control system that confirms that the original remote control is working properly. If it is normal, find the original machine maintenance repair
When Ding Ding industrial wireless remote control does not work (ie, the receiver does not respond to the corresponding action when pressing the transmitter button), and no fault message is generated, please follow the simple troubleshooting steps below to check Ding Ding Industrial Wireless Remote Control:
1. Check if the battery power is normal.
a. Check the battery model and installation direction.
b. Check the orientation of the battery compartment.
c. Check the battery level.
d. Check if the connection between the battery compartment and the circuit board is broken.
2. Check if the microprocessor control unit is faulty.
a. Unplug the transmitter key first, then plug the key switch again.
b. If you do not press the "Start" button, press the "Up, Down" and other action buttons directly. The transmitter should quickly flash a red light to indicate that the boot mode is incorrect. If not, it indicates that the microprocessor control unit is faulty or the power supply wiring is abnormal.
c. According to the normal start-up procedure, the power indicator light is red and the magnetic key cannot be started or removed. The magnet is missing or the magnetron on the circuit board is bad. Install a magnet or replace the magnetron. The emergency method can directly magnetize the magnet. The control ends are shorted.
Can't handle it yourself and get it repaired.
3. The transmitter LED is normal, but the receiver is completely unresponsive.
Make sure the receiver power input is normal.
a. Check whether the AC power fuse and DC power fuse are blown. If necessary, switch off the main power supply and replace the replacement fuse.
b. Make sure the wiring between the "receiving high frequency" module and the "relay" module is normal.
c. Confirm that the output fuse of the relay is blown. Replace the replacement fuse if necessary.
d. Confirm that the receiver and transmitter S/N code and the CH channel number are the same.
e. Check if the transmitter quartz crystal is broken or dropped off.
Send repairs
4, an action does not work
Check whether the output fuse of the relay is blown. If necessary, take the spare fuse and replace it with the control system that confirms that the original remote control is working properly. If it is normal, find the original machine maintenance repair
JINAN LODOR CNC EQUIPMENT CO.,LTD , https://www.zgfireplace.com